Related matters and process flow of Acoustic Wall

Acoustic Wall has brought a lot of convenience to our production and life, so what are the related matters and technological processes of Acoustic Wall? Let's take a look at it together.

Precautions before installation of Acoustic Wall

Acoustic Wall installation process

Precautions before installation of Acoustic Wall

1. The transportation and stacking of the Acoustic Wall should be on the side
   When installing the Acoustic Wall, to prevent it from being overturned and damaged, there should be square wood liners at both ends of the partition board. All mortar, concrete blocks, and miscellaneous materials that protrude from the wall, the ground, and the bottom of the floor shall be removed and cleaned; According to the drawing requirements, pop up the position line and side control line of the partition board on the top plate and bottom plate.

2. Strictly inspect the partition board
   Before installing the partition board, the partition board should be checked. Any unqualified product whose external dimensions exceed the required specifications or has defects shall not be used. The top of the partition board and the two grooves are spread with polymer mortar adhesive, starting from one end (if there are door and window openings on the partition wall, it should start from both sides of the door and window openings), and the board is erected, and the bottom Aim at the ink line and use a crowbar to tighten the top of the board on the bottom of the board so that it is aligned with the upper and lower position lines. The edge of the board is squeezed tightly, and the bottom of the board is pierced into the wooden wedge and wedge tightly. Use the line support board to level and straighten it, and then install the first two boards, squeeze the joints of the two boards tightly, and scrape the extruded adhesive. Check with a ruler to make the board straight, and use two sets of wooden wedges to plug the bottom of the board.

3. Fire test of Acoustic Wall
   The fire resistance limit of the Acoustic Wall exceeds 4 hours at a high temperature of 1000 degrees Celsius, it does not emit toxic gas, and its non-flammable performance reaches the national A-level specification.

4. Waterproof and moisture-proof test of Acoustic Wall

The Acoustic Wall can be cemented to form a pool filled with water without any waterproof finish. The back of the Acoustic Wall can remain dry without leaving any traces, nor will condensation droplets appear in humid climates. The panels of Acoustic Wall are professional waterproof boards with good waterproof and moisture-proof properties, which can be used in wet areas such as kitchens, clean rooms, and basements.

Acoustic Wall installation process

1. Paying off, lifting the board
   At the installation site of the Acoustic Wall panel, the elastic baseline is perpendicular to the baseline of the bottom of the board or the bottom of the beam to ensure that the installed wall panel is straight, and a 1.49-square-meter wall panel can be carried freely by two people.

2. Saw the board
   According to the requirements, use a portable machine to cut arbitrarily, and adjust the width and length of the Acoustic Wall panel to reduce the loss rate of the wall panel.

3. Sizing
   Use cement, medium sand (1:2), and building glue to make a paste, first wet the concave-convex groove of the wallboard with clean water, and then apply the polymer mortar in the concave-convex groove of the wallboard and the floor baseline.

4. Mounting the board
   Move the mortared Acoustic Wall panel to the assembly position and stand up, align the baseline position up and down, and use the iron pry to pry up the wall panel from the bottom and force the panel to abut against the panel.

5. In place
   Press the Acoustic Wall panel firmly against the joint to squeeze the mortar out of the joint, make sure the mortar is full, and temporarily secure it with a wooden wedge.

6. Correction
   Use a straight ruler to check the levelness and verticality of 2 meters: adjust the iron pry, and then fix it up and down with wooden wedges and steel bars.

7. Nail
   The connection part between the wallboard and the wallboard must be anchored with Φ6×200mm steel bars at an angle of 45°.

8. Fixed
   After correcting with 30×30mm wooden wedges on both sides, drill holes in the middle of the tenon or tenon and groove surface with an impact drill at a 45° angle, and then use Φ6×200mm steel bars to anchor.

9. Grouting
   Install the calibrated wallboard with cement mortar (1:2) plus construction glue to make polymer slurry to fill the upper and lower joints and the joints between the boards, and pull out the wooden wedges and fill them with mortar.

10. Slotted buried pipe
    If you want to bury hidden pipelines, switch boxes, etc., you can use an impact drill or a portable chainsaw to cut the wire trough to install, and then fill it with mortar polymer after installation.

11. Install the door frame
    The door frame can be covered with plywood directly on the Acoustic Wall panel, anchored to the wall with iron nails, and covered with decorative panels.

12. Apply paint

    
    

The final coat of paint can be applied. For example, if the tiles are pasted, there is no need to scrape the dust, and the tiles can be directly pasted on the wallboard with cement slurry, or directly pasted wallpaper, wood veneer, etc.

The above is the content related to Acoustic Wall-related matters and technological processes. If you are interested in soundproof walls, you can contact us. Our website is https://www.yhacoustic.com/, we look forward to seeing you and hope to work with you.